Suche nach „[Extern]“ hat 60 Publikationen gefunden

DigitalNachhaltigExtern

Beitrag (Sammelband oder Tagungsband)

F. Maiwald, Anton Schmailzl, S. Hierl

Thermo-mechanical computation of weld seam geometry in laser transmission welding

Applied Research Conference 2017, Berlin

DigitalNachhaltigExtern

Beitrag (Sammelband oder Tagungsband)

Johannes Käsbauer, Anton Schmailzl, S. Hierl

Simulative investigation on the influence of material- and process parameter on quasi-simultaneous laser transmission welding

Poster Session

Applied Research Conference 2017, Berlin

DigitalNachhaltigExtern

Zeitschriftenartikel

Anton Schmailzl, B. Quandt, M. Schmidt, S. Hierl

In-Situ process monitoring during laser transmission welding of PA6-GF30

Procedia CIRP, vol. 74, pp. 524-527

DOI: 10.1016/j.procir.2018.08.131

Abstract anzeigen

Quasi-simultaneous laser transmission welding is preferably used for packaging sensors and electronics. In order to protect the components from moisture, a hermetic encapsulation is needed. However, local weld seam interruptions cannot be identified with the commonly used set-path monitoring. By using a pyrometer, coaxially integrated into a 3D-scanner, gaps between the joining partners can be allocated on basis of the measured temperature. However, the scattering of the heat radiation, especially caused by the fiber reinforcement of the plastics, leads to a reduction of the accessible heat radiation, which makes the identification of gaps considerably more difficult. The herein used experimental setup is characterized by a small detection spot and only by a slight weakening of the heat radiation inside the scanner. Hence, for welding PA6-GF30, the detection of small sized gaps is possible, even if a glass fiber content of 30 percent (wt.) and a weld seam width with approximately 1 mm are given.

DigitalNachhaltigExtern

Beitrag (Sammelband oder Tagungsband)

Anton Schmailzl, S. Hüntelmann, T. Loose, Johannes Käsbauer, F. Maiwald, S. Hierl

Potentials of the ALE-Method for Modeling Plastics Welding Processes, in Particular for the Quasi-Simultaneous Laser Transmission Welding

Mathematical Modelling of Weld Phenomena 12, Graz, Österreich, vol. 12

ISBN: 978-3-85125-615-4

DOI: 10.3217/978-3-85125-615-4-51

Abstract anzeigen

The Arbitrary-Lagrangian-Eulerian-Method (ALE-Method) offers the possibility to model the quasi-simultaneous laser transmission welding of plastics, in which a squeeze-flow of molten plastic occurs. It is of great interest to get a deeper understanding of the fluid-structure-interactions in the welding zone, since the occurring squeeze-flow transports heated material out of the joining zone, causing a temperature decrease inside. In addition, the numerical modelling offers the possibility to investigate the flow conditions in the joining zone. The aim of this article is to show the potentials of the ALE-Method to simulate the quasi-simultaneous laser transmission welding with the commercially available software LS-DYNA. The central challenge is to realize a bi-directional thermo-mechanically coupled simulation, which considers the comparatively high thermal expansion and calculates the interactions of solid and melted plastic correctly. Finally, the potentials of the ALE element formulations for the mathematical description of welding processes are shown, especially for those with a squeeze-flow.

DigitalNachhaltigExtern

Vortrag

Johannes Käsbauer

Simulationsgestützte Prozessentwicklung beim Laser-Durchstrahlschweißen von Thermoplasten ohne absorbierende Füllstoffe

36. CADFEM ANSYS Simulation Conference, Leipzig

DigitalExtern

Beitrag (Sammelband oder Tagungsband)

Johannes Käsbauer, Anton Schmailzl, S. Hierl

Simulationsgestützte Prozessentwicklung beim Laser Durchstrahlschweißen von Thermoplasten ohne absorbierende Füllstoffe

Tagungsband zur 36. CADFEM ANSYS Simulation Conference (10.-12.10.2018; Leipzig)

DigitalNachhaltigExtern

Beitrag (Sammelband oder Tagungsband)

T. Heberholz, Andrey Prihodovsky, M. Nowottnick

Influence of a New Abnormal (CuNi)6Sn5 / (NiCu)3Sn4 Layer Growth at Temperatures Above 175°C in Tin Silver Based Lead-Free Solder Joints

Proceedings of the SMTA International Conference 2019 (22-26 September 2019; Rosemont, IL, USA)

DigitalNachhaltigExtern

Vortrag

T. Heberholz, Andrey Prihodovsky, M. Nowottnick

Einfluss eines abnormalen (CuNi)6Sn5/(NiCu)3Sn4-Schichtwachstums auf die Robustheit von bleifreien Zinn-Silber-Basis-Lotstellen bei Temperaturen oberhalb von 175 °C

Fachtagung/Konferenz EBL 2020 - Elektronische Baugruppen und Leiterplatten, Fellbach

DigitalNachhaltigExtern

Beitrag (Sammelband oder Tagungsband)

B. Quandt, Korbinian Schröcker, S. Hierl

Prozessüberwachung beim quasi-simultanen Laser-Durchstrahlschweißen glasfaserverstärkter Thermoplaste

9. Landshuter Leichtbau-Colloquium (2019), Landshut, vol. 9

ISBN: 978-3-9818439-2-7

DigitalNachhaltigExtern

Beitrag (Sammelband oder Tagungsband)

Anton Schmailzl, B. Quandt, S. Hierl, M. Schmidt

Correlation between Joint Strength and Process Temperature in Quasi-Simultaneous Laser Transmission Welding of Polyamide 6

Proceedings of LiM2019 - Lasers in Manufacturing (23 June 2019, Munich)

DigitalNachhaltigExtern

Zeitschriftenartikel

Anton Schmailzl, Johannes Käsbauer, J. Martan, P. Honnerová, F. Schäfer, Maximilian Fichtl, T. Lehrer, L. Prušáková, J. Tesař, J. Skála, M. Honner

Measurement of core temperature through semi-transparent polyamide 6 using scanner-integrated pyrometer in laser welding

International Journal of Heat and Mass Transfer, vol. 146, no. January

DOI: 10.1016/j.ijheatmasstransfer.2019.118814

Abstract anzeigen

Predicting the core temperature during welding is an ambitious aim in many research works. In this work, a 3D-scanner with integrated pyrometer is characterized and used to measure the temperature during quasi-simultaneous laser transmission welding of polyamide 6. However, due to welding in an overlap configuration, the heat radiation emitted from the joining zone of a laser transmission weld has to pass through the upper polymer, which is itself a semi-transparent emitter. Therefore, the spectral filtering of the heat radiation in the upper polymer is taken into account by calibrating the pyrometer for the measurement task. Thermal process simulations are performed to compare the temperature field with the measured temperature signal. The absorption coefficients of the polymers are measured, in order to get precise results from the computation. The temperature signals during welding are in good agreement with the computed mean temperature inside the detection spot, located in the joining area. This is also true for varying laser power, laser beam diameter and the carbon black content in the lower polymer. Both, the computed mean temperature and the temperature signal are representing the core temperature. In order to evaluate the spatial sensitivity of the measurement system, the emitted heat radiation from both polymers is calculated on basis of the computed temperature field. Hereby it is found, that more than 90 percent of the detected heat radiation comes from the joining area, which is a crucial information for contact-free temperature measurement tasks on semi-transparent polymers.

DigitalNachhaltigExtern

Zeitschriftenartikel

Johannes Käsbauer, Anton Schmailzl, U. Weber, S. Hierl, T. Jaus, M. Schwalme

Simulationsgestütze Evaluierung von Strahloszillationsmustern beim quasi-simultanen Laser-Durchstrahlschweißen.

Joining Plastics - Fügen von Kunststoffen, no. 2, pp. 102-109

DigitalNachhaltigExtern

Vortrag

Johannes Käsbauer, Anton Schmailzl, T. Loose, S. Hierl

Potentials of the EFG-Method for Modeling Quasi-Simultaneous Laser Transmission Welding Considering the Melt Flow

Simulationsforum 2019 Schweißen und Wärmebehandlung, Weimar

DigitalNachhaltigExtern

Vortrag

Johannes Käsbauer, Anton Schmailzl, T. Loose, S. Hierl

Thermo-Mechanical Modeling of Quasi-Simultaneous Laser Transmission Welding using LS-DYNA with Focus on Accuracy of Heat Input Calculation

Technology Day 2020 - Plastics on the test rig, Traboch, Österreich

DigitalNachhaltigExtern

Zeitschriftenartikel

Johannes Käsbauer, Anton Schmailzl, J. Prehm, T. Loose, S. Hierl

Simulation of Quasi-Simultaneous Laser Transmission Welding of Plastics: Optimization of Material Parameters in Broad Temperature Range

[Accepted for publication]

Procedia CIRP

Extern

W. Aschauer, H. Bähre, C. Chasovschi, Axel Dreyer, B. Eisenstein, J. Eisentraut, U. Fergen, J. Hanf, T. Harms, S. Haselwanter, C. Hausy, T. Herdin, F. Herle, Marcus Herntrei, K. Heuwinkel, Eric Horster, A. Kagermeier, E. Kreilkamp, I. Zur Oven-Krockhaus, Markus Pillmayer, J. Reif, Jens Rüdiger, M. Sand

Tourismus und Gesellschaft. Kontakte - Konflikte - Konzepte

22. Jahrestagung der Deutschen Gesellschaft für Tourismuswissenschaft (08.11. bis 10.11.2018, Fachhochschule Westküste, Heide)

Schriften zu Tourismus und Freizeit, vol. Band 24

ISBN: 978-3-503-18850-5

NachhaltigExtern

Beitrag (Sammelband oder Tagungsband)

Michael Laar, D. Garquitetura, F. Möhr

The Sustainable Urban Module / O Modulo Urbano Sustentável

Sustainable Revitalization of Tropical Cities/Revitalização Sustentável de Cidades, Rio de Janeiro/Berlin

Extern

M. Sackewitz, Fraunhofer-Allianz Vision

Leitfaden zur industriellen Röntgentechnik

Zerstörungsfreie Prüfung mit Bildverarbeitung

Vision, vol. 15

ISBN: 978-3-8396-0913-2

MobilExtern

Beitrag (Sammelband oder Tagungsband)

E. Fritz, R. Kircher, R. Palka, M. Witt, L. Blow, K. Eiler

Electromagnetic Fields related to High Speed Transportation Systems

ТРАНСПОРТНЫЕ СИСТЕМЫ И ТЕХНОЛОГИИ (Transportation Systems and Technology) - Conference Proceedings of Maglev2018 (5-8 September, 2018; St. Petersburg, Russia)

Extern

G. Prüller-Jagenteufel, H. Schelkshorn, F. Helm, C. Tauchner

Theologie der Befreiung im Wandel. Revisionen - Ansätze - Zukunftsperspektiven

Concordia: [...], Reihe Monographien, Aachen, vol. Bd. 51

ISBN: 978-3-86130-597-2