Publikationen


Suche nach „[Rolf] [Rascher]“ hat 193 Publikationen gefunden
Suchergebnis als PDF
    NachhaltigAngewandte Naturwissenschaften und WirtschaftsingenieurwesenIPH Teisnach

    Beitrag (Sammelband oder Tagungsband)

    Simon Killinger, Johannes Liebl, Rolf Rascher

    First steps towards an automated polishing process chain using one robot

    Proceedings of SPIE 11478 (Seventh European Seminar on Precision Optics Manufacturing [8 July 2020; Teisnach]), Bellingham, WA, USA

    2020

    DOI: 10.1117/12.2564840

    Abstract anzeigen

    Manufacturing precision optics is a complex process chain, which requires many operations on different machines. This is combined with operator-dependent steps such as manual cleaning, loading and measuring. In order to realize this process chain on a smaller shop area and to achieve a higher level of automation we build an operator-independent polishing cell. In this cell, an ABB robot serves as the actuator handling the workpiece. We positioned the robot in the center of the polishing cell to operate several workstations, so the whole process chain works with one single actuator. This arrangement allows a smaller and cheaper system, since no additional handling is required.

    NachhaltigAngewandte Naturwissenschaften und WirtschaftsingenieurwesenIPH Teisnach

    Beitrag (Sammelband oder Tagungsband)

    Michael Benisch, O. Fähnle, Rolf Rascher, Werner Bogner

    Force and pressure analysis during overarm polishing

    Proceedings of SPIE 11478 (Seventh European Seminar on Precision Optics Manufacturing [8 July 2020; Teisnach]), Bellingham, WA, USA

    2020

    DOI: 10.1117/12.2564903

    Abstract anzeigen

    The Preston-equation implies, that, besides the relative speed υrel and a specific constant KP, the pressure p plays a significant role for the removal rate when polishing an optical component. This paper demonstrates a possibility for a qualitative evaluation of the pressure distribution before the polishing process. A pressure-sensitive foil is used as a gauge for pressure measurement. The effectiveness of this measuring method is explained. Specific weaknesses and limitations in the use of these foils are discussed. A method for an integrated evaluation of the pressure on different spots of the polishing pad is proposed at the end of the paper.

    NachhaltigAngewandte Naturwissenschaften und WirtschaftsingenieurwesenIPH Teisnach

    Beitrag (Sammelband oder Tagungsband)

    M. Pohl, R. Börret, Olga Kukso, Rolf Rascher

    Mid spatial frequency error prevention strategies for the grinding process

    Proceedings of SPIE 11478 (Seventh European Seminar on Precision Optics Manufacturing [8 July 2020; Teisnach]), Bellingham, WA, USA

    2020

    DOI: 10.1117/12.2565261

    Abstract anzeigen

    This research is focused on the link between manufacturing parameters and the resulting mid-spatial frequency error in the manufacturing process of precision optics. The goal is to understand the generation mechanisms of mid-spatial frequency errors and avoid their appearance in the manufacturing process. Also, a simulation which is able to predict the resulting mid spatial frequency error from a manufacturing process is desired.

    NachhaltigAngewandte Naturwissenschaften und WirtschaftsingenieurwesenIPH Teisnach

    Beitrag (Sammelband oder Tagungsband)

    Olga Kukso, Rolf Rascher, M. Pohl, R. Börret

    On the metrology and analysis of MSF error

    Proceedings of SPIE 11478 (Seventh European Seminar on Precision Optics Manufacturing [8 July 2020; Teisnach]), Bellingham, WA, USA

    2020

    DOI: 10.1117/12.2566251

    Abstract anzeigen

    The aim of our research was to study middle spatial frequency errors (MSFE) on optical surfaces. We investigate the surfaces after manufacturing processes to find out the main affecting factors and to choose the proper processing parameters to minimize the size of the errors. To find an appropriate parameter window we have to be able not only to define the factors, which lead to MSFE, but also to analyze the change of the error after next following production steps.

    NachhaltigAngewandte Naturwissenschaften und WirtschaftsingenieurwesenIPH Teisnach

    Beitrag (Sammelband oder Tagungsband)

    M. Jung, Christian J. Trum, Beate Schmidbauer, E. Willenborg, Rolf Rascher

    Non-ablative removal of sub surface damages in ground optical glass substrates by controlled melting of thin surface layers using CO2-laser radiation

    Proceedings of SPIE 11478 (Seventh European Seminar on Precision Optics Manufacturing [8 July 2020; Teisnach]), Bellingham, WA, USA

    2020

    DOI: 10.1117/12.2564801

    Abstract anzeigen

    The form generation of optical surfaces by grinding and mechanical polishing results in small sub surface damages in the form of micro cracks that conventionally have to be removed by further removal of the damaged surface layers. In order to reduce process time and material cost non-ablative methods for removal of micro cracks are desired. Utilising the low optical penetration depths of less than 10 μm for CO2-laser radiation in glass, the laser energy can be used to heat up and melt thin surface layers. Using a 1.5 kW CO2-laser, a quasi-line focus formed by a scanner unit and a constant feed speed, it is possible to close all micro cracks present in the rough grinded test surfaces (max. SSD-depth ~ 63 μm), while achieving a process time of less than 2 seconds for a Ø 30 mm N-BK7 lens, respectively 7.5 seconds for fused silica. With a Sa as low as 50 nm and low distortion from the original shape the surfaces can directly be conventionally polished, further reducing the process chain complexity.

    NachhaltigAngewandte Naturwissenschaften und WirtschaftsingenieurwesenIPH Teisnach

    Beitrag (Sammelband oder Tagungsband)

    Sebastian Sitzberger, Johannes Liebl, Christian J. Trum, Rolf Rascher

    Concept of a two-part clamping system for lenses in optical metrology

    Proceedings of SPIE 11478 (Seventh European Seminar on Precision Optics Manufacturing [8 July 2020; Teisnach]), Bellingham, WA, USA

    2020

    DOI: 10.1117/12.2566547

    Abstract anzeigen

    The developed concept represents a universally applicable clamping system designed to fit in any measuring machine with any measuring principle. The design ensures that, as long as the lens remains clamped, the measurement results are reproducible. Form errors due to tension remain constant across all measuring and processing steps. The version presented in this paper was developed especially for small lenses in the diameter range up to 40 mm. On the one hand, the design allows for fast measurement of loose lenses. On the other hand, the device can also be used for measurement comparisons, since lenses can also be mounted permanently. In the following, the concept and first results of measurement tests are presented.

    NachhaltigAngewandte Naturwissenschaften und WirtschaftsingenieurwesenIPH Teisnach

    Beitrag (Sammelband oder Tagungsband)

    Armin Reif, Sebastian Sitzberger, Rolf Rascher

    Cutting high-performance materials with ultrasonically modulated cutting speed

    Proceedings of SPIE 11478 (Seventh European Seminar on Precision Optics Manufacturing [8 July 2020; Teisnach]), Bellingham, WA, USA

    2020

    DOI: 10.1117/12.2565757

    Abstract anzeigen

    The continuing trend towards lightweight construction and the associated machining rates of up to 95 % lead to an increased use of high-performance materials. The ever growing demands on the strength and quality of components and the associated use of materials which are hard to machine require the further development of new, economical machining techniques. In ultrasonic-assisted machining, an additional high-frequency vibration is superimposed on the conventional machining process. The vibration of the tool is usually excited axially or longitudinally to the workpiece, i.e. vertical to the cutting direction. An additional vibration overlay around the rotation axis (torsional) of the tool is also possible. This generates a vibration overlay in the cutting direction. The vibration initiation causes vibration amplitudes in the range of a few micrometers at the tool cutting edge. This leads in turn to a high-frequency change in the cutting speed or feed rate. Overall, an additional torsional vibration overlap can further reduce cutting forces, increase tool life and improve workpiece quality. In order for a grinding tool to generate a torsional vibration, a special tool was required that had to be designed by simulation. The formation of a torsional vibration was achieved by helical slots in the sonotrode. Depending on the angle of rotation and the length of the slots, a part of the axial vibration is converted into a torsional vibration by an axial excitation of the sonotrode. The aim in designing the slots was to achieve the highest possible vibration amplitude. Following the simulation, the slots were inserted into the tool in the corresponding optimum geometric position. Afterwards, the specially designed grinding tool was validated by machining the brittle-hard glass-ceramic material Zerodur. The first test results with the torsionally vibrating tool are presented in the following.

    NachhaltigAngewandte Naturwissenschaften und WirtschaftsingenieurwesenIPH Teisnach

    Zeitschriftenartikel

    Armin Reif, P. Rinck, Sebastian Sitzberger, Rolf Rascher, M. Zäh

    Zerspanung von Hochleistungswerkstoffen mit ultrasonisch modulierter Schnittgeschwindigkeit

    ZWF - Zeitschrift für wirtschaftlichen Fabrikbetrieb, vol. 115, no. 3, pp. 2-5

    2020

    DOI: 10.3139/104.112255

    Abstract anzeigen

    Die steigenden Anforderungen an die Festigkeit und die Qualität von Bauteilen und die damit verbundene Verwendung hochfester Materialien erfordert die Weiterentwicklung neuer wirtschaftlicher Zerspanungstechniken. Durch eine werkzeugseitige Schwingungsüberlagerung können bei der Bearbeitung von schwer zerspanbaren Werkstoffen die Zerspankräfte und der Werkzeugverschleiß reduziert sowie die Oberflächenqualität verbessert werden.

    NachhaltigAngewandte Naturwissenschaften und WirtschaftsingenieurwesenIPH Teisnach

    Vortrag

    Simon Killinger, Alexander Haberl, Rolf Rascher

    Analysis of residual errors during computer controlled polishing

    EOS Optical Technologies: Conference on Manufacturing, Tolerancing and Testing of Optical Systems (MOS) – Session 7: Plenary Session, München

    2019

    Abstract anzeigen

    In computer controlled subapertur polishing the formation of mid spatial frequency errors (MSFE) needs special attention. In this work the formation of MSFE in feed direction is investigated using the ADAPT tool from Satisloh.

    NachhaltigAngewandte Naturwissenschaften und WirtschaftsingenieurwesenIPH Teisnach

    Vortrag

    Sebastian Sitzberger, P. Rinck, A. Gueray, Rolf Rascher

    Ultraschallunterstützte Zerspanung von Advanced Materials

    3. Wissenschaftliches Forum zur ULTRASONIC-Bearbeitung, Jena

    2019

    NachhaltigAngewandte Naturwissenschaften und WirtschaftsingenieurwesenIPH Teisnach

    Vortrag

    Sebastian Sitzberger, J. Reitberger, Rolf Rascher

    Clamping system for optical components for adaptation in optical production

    10th HLEM 2019 - High Level Expert Meeting Asphere Metrology on Joint Investigations, Braunschweig

    2019

    NachhaltigAngewandte Naturwissenschaften und WirtschaftsingenieurwesenIPH Teisnach

    Beitrag (Sammelband oder Tagungsband)

    Michael Benisch, Werner Bogner, Rolf Rascher

    Using A Digital Temperature Sensor To Measure The Temperature Development During A Polishing Process

    Proceedings of the 2019 EOS Optical Technologies Conference

    2019

    NachhaltigAngewandte Naturwissenschaften und WirtschaftsingenieurwesenIPH Teisnach

    Beitrag (Sammelband oder Tagungsband)

    M. Pohl, U. Bielke, R. Börret, Rolf Rascher, Olga Kukso

    MSF-error prevention strategies for the grinding process

    Proceedings of SPIE 11171 (Sixth European Seminar on Precision Optics Manufacturing, 1117101 [9-10 April 2019, Teisnach]), Bellingham, WA, USA

    2019

    DOI: 10.1117/12.2526581

    Abstract anzeigen

    This research is focused on the link between manufacturing parameters and the resulting mid-spatial frequency error in the manufacturing process of precision optics. This third publication focuses on strategies of avoidance and generation mechanisms of the mid-spatial frequency errors from the grinding process. The Goal is to understand the generation mechanisms of the mid-spatial frequency errors and avoid their appearance in the manufacturing process.

    NachhaltigAngewandte Naturwissenschaften und WirtschaftsingenieurwesenIPH Teisnach

    Beitrag (Sammelband oder Tagungsband)

    Sebastian Sitzberger, Johannes Liebl, J. Reitberger, Rolf Rascher

    Zero-point clamping systems in optical production

    Proceedings of SPIE 11171 (Sixth European Seminar on Precision Optics Manufacturing, 1117101 [9-10 April 2019, Teisnach]), Bellingham, WA, USA

    2019

    DOI: 10.1117/12.2528774

    Abstract anzeigen

    Zero point clamping systems are an integral part of the manufacturing industry. They have only yet to find their way into the optical industry. This article compares the hydraulic expansion holder, a clamping system currently used in the optical industry with a zero-point clamping system. The achievable accuracies of both systems are compared over several measurement series. In addition, the process capability evaluation is used for the comparison. Finally, the results are summarized to provide every researcher and practitioner with a foundation for assessing whether zero point clamping systems meet the requirements for the use in optical manufacturing.

    NachhaltigAngewandte Naturwissenschaften und WirtschaftsingenieurwesenIPH Teisnach

    Beitrag (Sammelband oder Tagungsband)

    Simon Killinger, Johannes Liebl, Rolf Rascher

    Mid-spatial frequency errors in feed direction occurring in ADAPT polishing

    Proceedings of SPIE 11171 (Sixth European Seminar on Precision Optics Manufacturing, 1117101 [9-10 April 2019, Teisnach]), Bellingham, WA, USA

    2019

    DOI: 10.1117/12.2528114

    Abstract anzeigen

    Previous work shows the effectiveness of computer controlled polishing (CCP) with the ADAPT tool by Satisloh for correcting form errors in optics manufacturing. This method however has a risk of producing residual errors in the range of mid spatial frequency errors (MSFE). In order to prevent these errors the residual in feed direction is investigated as well as the behavior at different parameters.

    DigitalNachhaltigAngewandte Naturwissenschaften und WirtschaftsingenieurwesenIPH Teisnach

    Beitrag (Sammelband oder Tagungsband)

    M. Doetz, O. Dambon, Christian Vogt, Rolf Rascher, E. Langenbach, O. Fähnle

    Enlarging process window of ductile mode machining of WC molds

    Proceedings of EOSAM 2018 (European Optical Society Biennial Meeting; October 2018; Delft, The Netherlands): Optical System Design, Tolerancing, and Fabrication

    2018

    DigitalNachhaltigAngewandte Naturwissenschaften und WirtschaftsingenieurwesenIPH Teisnach

    Beitrag (Sammelband oder Tagungsband)

    Christian J. Trum, Christian Vogt, O. Fähnle, Sebastian Sitzberger, Rolf Rascher

    First experiences with Filled-Up-Microscopy (FUM) to evaluate the depth of sub-surface damages on ground surfaces

    Proceedings of EOSAM 2018 (European Optical Society Biennial Meeting; October 2018; Delft, The Netherlands): Optical System Design, Tolerancing, and Fabrication

    2018

    DigitalNachhaltigAngewandte Naturwissenschaften und WirtschaftsingenieurwesenIPH Teisnach

    Beitrag (Sammelband oder Tagungsband)

    Christian Vogt, M. Doetz, Rolf Rascher, O. Fähnle

    Standardized evaluation of grinding tools for brittle and ductile mode grinding

    Invited Paper

    Proceedings of EOSAM 2018 (European Optical Society Biennial Meeting; October 2018; Delft, The Netherlands): Optical System Design, Tolerancing, and Fabrication

    2018

    DigitalNachhaltigAngewandte Naturwissenschaften und WirtschaftsingenieurwesenIPH Teisnach

    Vortrag

    Rolf Rascher

    Grinding and polishing of glass - Basis for a perfect coating

    12th International Conference on Coatings on Glass and Plastics (Joint session of DGG-Glasforum and the ICCG): The Glass Surface - The Basis for Innovative Coatings, Würzburg

    2018

    DigitalNachhaltigAngewandte Naturwissenschaften und WirtschaftsingenieurwesenIPH Teisnach

    Vortrag

    Rolf Rascher, Christian Vogt, O. Fähnle, E. Langenbach

    Closed-loop laser polishing of glass

    LaP 2018 - 3rd Conference on Laser Polishing, Aachen

    2018