Publikationen


Suche nach „[Peter] [Landstorfer]“ hat 6 Publikationen gefunden
Suchergebnis als PDF
    DigitalFraunhofer AWZ CTMTMaschinenbau und Mechatronik

    Zeitschriftenartikel

    Jochen Hiller, Peter Landstorfer, Philipp Marx, Matthias Herbst

    Evaluation of the impact of faulty scanning trajectories in robot-based x-ray computed tomography

    Measurement Science and Technology, vol. 32, no. 1

    2020

    DOI: 10.1088/1361-6501/abaf2a

    Abstract anzeigen

    X-ray computed tomography (CT) imaging for industrial applications is limited to certain physical conditions to be fulfilled. The size of the measuring object and the accumulated wall thickness are two fundamental conditions. An omission of these conditions by not capturing object attenuation information by the x-ray detector leads to missing data in the 3D reconstruction process and results as a consequence in image degradation and artifacts. Conventional industrial x-ray CT is based on cone-beam projections and circular or helical scanning trajectories using linear axis and a rotary (lift) table. For many inspection tasks on big-sized or unusually shaped objects the physical limits for obtaining a sufficient high image quality are reached very quickly when using conventional CT systems. Industrial six-axis robots offer much more flexibility with respect to the conditions mentioned earlier and can overcome the limitations of conventional scanners. In the present work we characterized an industrial six-axis robot in its working space following ISO 9283 in terms of pose accuracy and pose repeatability. These results are then used to simulate faulty scanning trajectories in terms of pose deviations where a single robot is used as an object manipulator to rotate virtual specimens on a circular trajectory resulting in different (faulty) reconstruction datasets. These datasets are evaluated visually and by using performance parameters and geometrical features in order to determine the reproduction fidelity (performance) of a one arm robot-based CT system depending on different pose errors. With the results obtained it was shown that a robot-based CT system of type B (in our classification scheme) using one robot as object manipulator should be able to reach a spatial resolution power in the range of the voxel size (in our case 200 µm) and smaller (neglecting effects from focal spot size, detector unsharpness from x-ray to light conversation and scatter radiation) if systematic pose errors are compensated using appropriate calibration methods.

    DigitalFraunhofer AWZ CTMTMaschinenbau und Mechatronik

    Beitrag (Sammelband oder Tagungsband)

    Peter Landstorfer, Gabriel Herl, Jochen Hiller

    Investigation of Non-circular Scanning Trajectories in Robot-based Industrial X-ray Computed Tomography of Multi-material Objects

    16th International Conference on Informatics in Control, Automation and Robotics (ICINCO) [29-31 July, 2019; Prague, Czech Republic]

    2019

    DigitalFraunhofer AWZ CTMTMaschinenbau und Mechatronik

    Beitrag (Sammelband oder Tagungsband)

    Peter Landstorfer, Jochen Hiller, Matthias Herbst

    Investigation of positioning accuracy of industrial robots for robotic-based X-ray computed tomography

    iCT 2019 9th Conference on Industrial Computed Tomography (iCT) [13-15 February, 2019; Padua, Italy]

    2019

    Abstract anzeigen

    In this research work we investigated the accuracy of a standard industrial robot. We wanted to find out, how accurate an X-RayComputed Tomography (CT) scan can be performed when using such a robot as a manipulator. The accuracy was measuredusing a laser-interferometer. The measured deviations were used to run an X-Ray simulation via Fraunhofer EZRT’s ScorpiusX-Lab. Metrological analysis was performed as a measure for the quality of the simulated CT-scan. The metrological deviationsreflect the feasible accuracy of a CT-scan in a real CT-setup.

    DigitalFraunhofer AWZ CTMTMaschinenbau und Mechatronik

    Zeitschriftenartikel

    Peter Landstorfer, Jochen Hiller

    Präzision in drei Freiheitsgraden - Exakte Bauteilpositionierung bei CT-Messungen ohne zusätzliche Antriebe

    inspect, no. 2

    2015

    Abstract anzeigen

    Die präzise und reproduzierbare Ausrichtung von Messobjekten im CT ist eine wesentliche Voraussetzung für die Erzeugung vollständiger und genauer Datensätze. Mit einer universellen Positioniereinheit für industrielle Computertomographen (CT), die vollständig von den im Gerät vorhandenen Achsen angetrieben wird und dabei eine Ausrichtung von Messobjekten in drei Freiheitsgraden ermöglicht, wird dies in Zukunft einfacher zu realisieren sein.

    DigitalFraunhofer AWZ CTMTMaschinenbau und Mechatronik

    Beitrag (Sammelband oder Tagungsband)

    Peter Landstorfer, Thomas Miller, Jochen Hiller

    Automatisierung von Mess- und Prüfprozessen mit Computertomographie

    Leitfaden zur industriellen Röntgentechnik, vol. 15

    2015

    ISBN: 978-3-8396-0913-2

    DigitalMaschinenbau und Mechatronik

    Zeitschriftenartikel

    Peter Landstorfer, Thomas Miller

    Effizientere Messvorgänge durch Automatisierung: Der Computertomograph erhält Hilfe vom Roboter

    Quality Engineering, no. 3

    2015