Publikationen


Suche nach „[Liebl] [Johannes]“ hat 27 Publikationen gefunden
Suchergebnis als PDF
    NachhaltigAngewandte Naturwissenschaften und WirtschaftsingenieurwesenIPH Teisnach

    Beitrag (Sammelband oder Tagungsband)

    Jakob Reitberger, Rolf Rascher, Johannes Liebl, Sebastian Sitzberger

    Zero-point clamping systems in optical production

    Proceedings of SPIE 11171 (Sixth European Seminar on Precision Optics Manufacturing, 1117101 [April 9th-10th 2019, Teisnach]), Bellingham, WA, USA

    2019

    DOI: 10.1117/12.2528774

    Abstract anzeigen

    Zero point clamping systems are an integral part of the manufacturing industry. They have only yet to find their way into the optical industry. This article compares the hydraulic expansion holder, a clamping system currently used in the optical industry with a zero-point clamping system. The achievable accuracies of both systems are compared over several measurement series. In addition, the process capability evaluation is used for the comparison. Finally, the results are summarized to provide every researcher and practitioner with a foundation for assessing whether zero point clamping systems meet the requirements for the use in optical manufacturing.

    NachhaltigAngewandte Naturwissenschaften und WirtschaftsingenieurwesenIPH Teisnach

    Beitrag (Sammelband oder Tagungsband)

    Rolf Rascher, Johannes Liebl, S. Killinger

    Mid-spatial frequency errors in feed direction occurring in ADAPT polishing

    Proceedings of SPIE 11171 (Sixth European Seminar on Precision Optics Manufacturing, 1117101 [April 9th-10th 2019, Teisnach]), Bellingham, WA, USA

    2019

    DOI: 10.1117/12.2528114

    Abstract anzeigen

    Previous work shows the effectiveness of computer controlled polishing (CCP) with the ADAPT tool by Satisloh for correcting form errors in optics manufacturing. This method however has a risk of producing residual errors in the range of mid spatial frequency errors (MSFE). In order to prevent these errors the residual in feed direction is investigated as well as the behavior at different parameters.

    NachhaltigAngewandte Naturwissenschaften und WirtschaftsingenieurwesenIPH Teisnach

    Zeitschriftenartikel

    G. Berger, I. Widdershoven, M. Schulz, R. Bergmann, D. Ramm, A. Beutler, J. Asfour, G. Schneider, T. Blümel, C. Elster, R. Meeß, H. Klawitter, R. Schachtschneider, M. Sandner, I. Fortmeier, K. Kubo, F. Löffler, Johannes Liebl, M. Stavridis, M. Wendel, C. Pruss

    Interlaboratory comparison measurements of aspheres

    Measurement Science and Technology, vol. 29, no. 5

    2018

    DOI: 10.1088/1361-6501/aaae96

    Abstract anzeigen

    The need for high-quality aspheres is rapidly growing, necessitating increased accuracy in their measurement. A reliable uncertainty assessment of asphere form measurement techniques is difficult due to their complexity. In order to explore the accuracy of current asphere form measurement techniques, an interlaboratory comparison was carried out in which four aspheres were measured by eight laboratories using tactile measurements, optical point measurements, and optical areal measurements. Altogether, 12 different devices were employed. The measurement results were analysed after subtracting the design topography and subsequently a best-fit sphere from the measurements. The surface reduced in this way was compared to a reference topography that was obtained by taking the pointwise median across the ensemble of reduced topographies on a $1000 \times 1000$ Cartesian grid. The deviations of the reduced topographies from the reference topography were analysed in terms of several characteristics including peak-to-valley and root-mean-square deviations. Root-mean-square deviations of the reduced topographies from the reference topographies were found to be on the order of some tens of nanometres up to 89 nm, with most of the deviations being smaller than 20 nm. Our results give an indication of the accuracy that can currently be expected in form measurements of aspheres.

    NachhaltigAngewandte Naturwissenschaften und WirtschaftsingenieurwesenIPH Teisnach

    Beitrag (Sammelband oder Tagungsband)

    Gerald Fütterer, Rolf Rascher, C. Pruß, H. Harsch, W. Osten, Alexander Haberl, Johannes Liebl

    Model based error separation of power spectral density artefacts in wavefront measurement

    Proceedings of SPIE 10749 (SPIE Optical Engineering + Applications Conference on Interferometry XIX [August 19-23, 2018; San Diego, CA, USA])

    2018

    DOI: 10.1117/12.2321106

    NachhaltigAngewandte Naturwissenschaften und WirtschaftsingenieurwesenIPH Teisnach

    Beitrag (Sammelband oder Tagungsband)

    Gerald Fütterer, Alexander Haberl, Johannes Liebl

    Contribution of the phase transfer function of extended measurement cavities to mid spatial frequencies and the overall error budget

    Proceedings of SPIE 10829 (Fifth European Seminar on Precision Optics Manufacturing [April 10-11, 2018; Teisnach])

    2018

    ISBN: 978-1-5106-2270-8

    DOI: 10.1117/12.2318711

    Abstract anzeigen

    A challenge of coaxial - measurement cavity based - interferometer is to realize an interference contrast in the vicinity of one and to realize a complete elimination of the parasitic reflections. Another challenge, which also exists in non-coaxial setups, is the phase transfer function of extended measurement cavities. Ideally, the surface under test (SUT) and the reference surface (REF) are both exactly imaged onto the detector plane. In practice, SUT and REF have to be placed within the depth of field (DOF), which refers to the object space. The term depth of focus refers to the image space. To avoid confusion, the depth of field might be referred to as DOOF (depth of object field) and the depth of focus might be referred to as DOIF (depth of image field). However, in many measurement situations, the REF is not placed within the DOOF, which is the small z-range, which is imaged onto the detector plane. Furthermore, the phase transfer function (PTF) of the REF and the image distortion of the REF are both dependent on the focal plane used to image the SUT onto the detector plane. Effects as phase deformation, image distortion and image blurring have to be taken into account when using extended measurement cavities. This can be done by using a look up table (LUT), which contains simulated and/or calibrated data. Thus, the related system error can be subtracted. A remaining challenge is an unknown object under test (OUT), which is measured by using a double path arrangement. The measured wave front depends on the two surfaces of the OUT and the position of the return mirror. For simplicity, a homogeneous substrate and a perfect return mirror might be presumed. The simulation of waves propagating within extended measurement cavities, as well as measurement results, will be discussed. In addition, the influence on the power spectral density (PSD) will be described. This is important for high end correction techniques as e.g. magneto rheological figuring (MRF) and ion beam figuring (IBF).

    NachhaltigAngewandte Naturwissenschaften und WirtschaftsingenieurwesenIPH Teisnach

    Beitrag (Sammelband oder Tagungsband)

    Rolf Rascher, Christian Schopf, Johannes Liebl

    DefGO

    Proceedings of SPIE 10829 (Fifth European Seminar on Precision Optics Manufacturing [April 10-11, 2018; Teisnach])

    2018

    ISBN: 978-1-5106-2270-8

    DOI: 10.1117/12.2318704

    Abstract anzeigen

    The manufacturing of optical lenses has various steps. Generally, the manufacturing can be split up into the following steps: the workpiece is pre-ground with a coarse tool; it is then fine-ground with a finer tool. As the final polishing is a demanding and time-consuming process that cannot manage large removal rations not can it equalise rough shape errors, the starting quality and surface quality needs to be as high as possible. According to the current state of technology, ground lenses must be measured with tactile measuring techniques in order to detect shape errors. This is timeconsuming and expensive, and only two dimensional profiles can be measured. DefGO’s project objective is to introduce deflectometry as a new, three dimensional lens measuring standard. A problem with the application of deflectometry is that the object to be measured has to reflect enough light, which is not the case for ground glass with rough surfaces. DefGO’s solution is to wet the lens with a fluid to create a closed reflecting surface.

    NachhaltigAngewandte Naturwissenschaften und WirtschaftsingenieurwesenIPH Teisnach

    Beitrag (Sammelband oder Tagungsband)

    Rolf Rascher, Alexander Haberl, Johannes Liebl

    ABC-polishing

    Proceedings of SPIE 10829 (Fifth European Seminar on Precision Optics Manufacturing [April 10-11, 2018; Teisnach])

    2018

    ISBN: 978-1-5106-2270-8

    DOI: 10.1117/12.2318549

    Abstract anzeigen

    In the past, steadily increasing demands on the imaging properties of optics have led more and more precise spherical apertures. For a long time, these optical components have been produced in a satisfying quality using classic polishing methods such as pitch polishing. The advance of computer-controlled subaperture (SA) polishing techniques improved the accuracy of spheres. However, this new machine technology also made it possible to produce new lens geometries, such as aspheres. In contrast to classic polishing methods, the high determinism of SA polishing allows a very specific correction of the surface defect. The methods of magneto-rheological finishing (MRF) [1], [2] and ion beam figuring (IBF) [3], [4] stand out in particular because of the achievable shape accuracy. However, this leads to the fact that a principle of manufacturing "As exact as possible, as precise as necessary" [5] is often ignored. The optical surfaces often produced with unnecessary precision, result at least in increased processing times. The increasing interconnection of the production machines and the linking with databases already enables a consistent database to be established. It is possible to store measurements, process characteristics or tolerances for the individual production steps in a structured way. The difficulty, however, lies in the reasonable evaluation of the measurement data. This is where this publication comes in. The smart evaluation of the measurement data with the widespread Zernike polynomials should result in a classification, depending on the required manufacturing tolerance. In combination with the so-called ABC analysis, all surface defects can be categorized. In this way, an analytic breakdown of a - initially confusing - overall problem is made. With the aid of cost functions [6] an evaluation and consequently a deduction of actions is made possible. Thus, for example, the isolated processing of rotationally symmetrical errors in spiral mode, setup times and machining times can be reduced while avoiding mid spatial frequency errors (MSFE) at the same time.

    NachhaltigAngewandte Naturwissenschaften und Wirtschaftsingenieurwesen

    Beitrag (Sammelband oder Tagungsband)

    Rolf Rascher, Christian Schopf, Johannes Liebl

    Cheap and fast measuring roughness on big surfaces with an imprint method

    Proceedings of SPIE 10448 (SPIE Optifab [October 16-19, 2017; Rochester, NY, USA])

    2017

    NachhaltigAngewandte Naturwissenschaften und Wirtschaftsingenieurwesen

    Zeitschriftenartikel

    J.-P. Richters, Rolf Rascher, Johannes Liebl, Engelbert Hofbauer, Manon Schilke

    Deflectometric Acquisition of Large Optical Surfaces “DaOS” Using a New Physical Measurement Principle: Vignetting Field Stop

    (Reprinted from Proceedings of SPIE Volume 10009: Third European Seminar on Precision Optics Manufacturing, 100090Y [Teisnach, April 12th 2016] doi:10.1117/12.2236134)

    Bavarian Journal of Applied Sciences, no. 2, pp. 146-161

    2016

    Abstract anzeigen

    The vignetting field stop procedure uses a deflectometric approach to acquire big Optical Surfaces – DaOS – and it offers the possibility to measure nearly any shape or form using a scanning routine. The basic physical measurement principle in DaOS is the vignettation of a quasi-parallel light beam emitted by an expanded light source in auto collimation arrangement with a reflecting element. Thereby nearly any curvature of the specimen, is measurable. Due to the fact, that even sign changes in the curvature can be detected, also aspheres and freeform surfaces of any size can be evaluated. In this publication the vignetting field stop procedure is discussed. Additionally the deflectometric setup is described. Because of some typical influences of beam deflection to the accuracy of angle measurement by using the vignetting principle, suitable methods of calibration for the sensor are examined and the results of these methods are presented. Furthermore, the technical principle of deflectometric measurements using an angle detecting device is explained inclusive of all random and systematic errors generated by the setup. The last part of this publication shows the actual result of test measurements with calculated absolute deviation of errors with a large lateral dimension as well as the determination of the maximal achievable lateral resolution by detecting mid frequent structures on flat and spherical test parts with a diameter of 300 mm. These measurements are compared critically to reference results which are recorded by interferometry and further scanning methods.

    NachhaltigAngewandte Naturwissenschaften und Wirtschaftsingenieurwesen

    Beitrag (Sammelband oder Tagungsband)

    J.-P. Richters, Rolf Rascher, Johannes Liebl, Engelbert Hofbauer, Manon Schilke

    Deflectometric acquisition of large optical surfaces (DaOS) using a new physical measurement principle: vignetting field stop procedure

    Proceedings of SPIE 10009 (Third European Seminar on Precision Optics Manufacturing, 100090Y [April 12th 2016, Teisnach])

    2016

    DOI: 10.1117/12.2236134

    NachhaltigAngewandte Naturwissenschaften und Wirtschaftsingenieurwesen

    Beitrag (Sammelband oder Tagungsband)

    Christine Wünsche, Johannes Liebl, Manon Schilke

    Surface reconstruction by using Zernike polynomials

    Proceedings of SPIE 10009 (Third European Seminar on Precision Optics Manufacturing, 100090Y [April 12th 2016, Teisnach])

    2016

    DOI: 10.1117/12.2236305

    Abstract anzeigen

    The development of high precision methods for the measurement of plano surfaces became of increasing importance over the last years. Recently accuracies in sub-nanometer range have been achieved on samples up to one meter in diameter. The used measurement method was based on direct deflectometry. The main part of the system was an electronic autocollimator measuring local angular displacements on defined traces along the surface of the plano lens. To stabilize the optical path a pentaprism was used. The measurement accuracy of a similar system was evaluated at the Technologie Campus Teisnach. The used system delivered twenty measurement spots along the profile on one diameter. Four diameters were measured at every 45 degrees. An evaluation algorithm was developed to model the complete threedimensional surface out of a small amount of measurement points. Within this modelling Zernike polynomials were used to reconstruct the surface topography. Two different approaches in using the hierarchy of the polynomials were compared. At first a reference surface was created by rotating a symmetrical averaged curve of all measured profiles. On the residuals of the original measurements to the symmetrical averaged curve a serial development of the error surface was applied with the help of Zernike polynomials. Different order of Zernike terms were tested because we saw a big influence on the result. This surface was added to the reference surface. The results of the two different approaches were compared. To enable us to compare the results of this measurement method to interferometric and optical 3Dprofilometric measurements the data was converted to xyz-format. © (2016) COPYRIGHT Society of Photo-Optical Instrumentation Engineers (SPIE). Downloading of the abstract is permitted for personal use only.

    NachhaltigAngewandte Naturwissenschaften und Wirtschaftsingenieurwesen

    Beitrag (Sammelband oder Tagungsband)

    Rolf Rascher, Horst Linthe, Johannes Liebl, Sebastian Sitzberger

    Interferometric measurement of highly accurate flat surfaces

    Proceedings of SPIE 10009 (Third European Seminar on Precision Optics Manufacturing, 100090Y [April 12th 2016, Teisnach])

    2016

    DOI: 10.1117/12.2235525

    Abstract anzeigen

    The most important part in manufacturing precision optics is a reliable measurement procedure which provides results a few times more accurate than the quality to be produced. In general two specific values are important, the repeatability of several measurements which are done in a row and the absolute accuracy which is mostly defined by the systematical error of the measurement device. The repeatability can be improved relatively simple, by increasing the number of measurements and a following averaging step. To increase the absolute accuracy of a measurement device in the field of precision optics is far more challenging. In this paper several interferometer absolute testing methods to measure flat surfaces are compared. The main objective was to name a value for the achievable accuracy. Therefor four different methods were analyzed: 1. The three flat test, a method which is already used several decades to determine the quality of a flat surface. As a result, two absolute measured profiles, horizontal and vertical, can be calculated. 2. The multi rotation test, an extension of the classical three flat test. The big advantage of this method is a fully three dimensional map of the systematical error. 3. The systematical error calculated by the SSI-A. Hereby several subapertures are measured over the whole surface. The redundant information’s of the overlapping regions can be used to calculate the systematical error of the system. 4. The rotation of the transmission flat relatively to the interferometer. Thereby the rotation unsymmetrical errors can be calculated and subtracted. © (2016) COPYRIGHT Society of Photo-Optical Instrumentation Engineers (SPIE). Downloading of the abstract is permitted for personal use only.

    NachhaltigAngewandte Naturwissenschaften und Wirtschaftsingenieurwesen

    Beitrag (Sammelband oder Tagungsband)

    J.-P. Richters, Felix Friedke, Rolf Rascher, Thomas Stubenrauch, Johannes Liebl, Engelbert Hofbauer

    The vignetting field stop procedure: A new physical measurement principle for the Deflectometric acquisition of big Optical Surfaces - DaOS

    DGaO Proceedings (116. Jahrestagung in Brno, Tschechische Republik, 25.-29.05.2015)

    2015

    Angewandte Naturwissenschaften und Wirtschaftsingenieurwesen

    Zeitschriftenartikel

    Christine Wünsche, Heiko Biskup, Rolf Rascher, Sebastian Draxinger, Johannes Liebl

    Process developement fort the reproducible roughness measurement of optical surfaces using white light interferometry

    International Journal of Metrology and Quality Engineering (EDP Sciences), vol. 5, no. 1, pp. 29-35

    2014

    Angewandte Naturwissenschaften und Wirtschaftsingenieurwesen

    Beitrag (Sammelband oder Tagungsband)

    O. Fähnle, Christine Wünsche, Heiko Biskup, Rolf Rascher, E. Langenbach, F. Frost, A. Schindler, Johannes Liebl

    Generation and field testing of roughness reference samples for industrial testing of surface roughness levels below 0.5nm Sq

    Proceedings of EOSAM 2014 (European Optical Society Annual Meeting) [Sep 15-19 2014, Berlin, Germany]

    2014

    Angewandte Naturwissenschaften und Wirtschaftsingenieurwesen

    Beitrag (Sammelband oder Tagungsband)

    Roland Maurer, Rolf Rascher, Thomas Stubenrauch, et al., Johannes Liebl, Engelbert Hofbauer

    Approach to the measurement of astronomical mirrors with new procedures

    Optical Metrology 2013, Optical Measurement Systems for Industrial Inspection VIII, volume 8788

    2013

    Angewandte Naturwissenschaften und Wirtschaftsingenieurwesen

    Vortrag

    Johannes Liebl

    Messportal TC Teisnach

    6. Optikseminar - Agenda zur modernen Optikfertigung, Teisnach

    2013

    Angewandte Naturwissenschaften und Wirtschaftsingenieurwesen

    Vortrag

    Rolf Rascher, Katharina Dieser, Johannes Liebl

    GF-Projekt Optasens - Combination and evaluation of different optical and tactile sensor and measuring methods for analysis and global form-measurement on optical surfaces

    Posterpräsentation

    F.O.M.-Marktplatz der Forschungsprojekte, Berlin

    2012

    Angewandte Naturwissenschaften und Wirtschaftsingenieurwesen

    Zeitschriftenartikel

    Johannes Liebl

    Dreistrahllaserinterferometrie zur Topographievermessung ebener Flächen

    Photonik - Fachzeitschrift für die optischen Technologien, vol. 4, pp. 38-40

    2012

    Angewandte Naturwissenschaften und Wirtschaftsingenieurwesen

    Vortrag

    Rolf Rascher, et al., Johannes Liebl

    Hochgenaue Optische Abstandssensoren in Messtechnik und Qualitätssicherung

    1. Optence Messtechnik Symposium, Darmstadt

    2012